Wilson Combat Deluxe Bullet Proof Sear, A-2

Very well machined!..

When compared side by side with my stock Springfield sear it disgusted me that they would put something so terribly machined in a 1911! The Wilson sear however was perfect, no tooling marks very shiny and polished unlike the picture. It was worth the money. I matched it with an STI trigger, Wilson Spec Ops 9 hammer, and Wilson stainless steel disconnector. I was blown away at how it all was drop in and how crisp the trigger pull was! Thanks Wilson!

very nice..

dropped right in, no fitting, along with the wilson trigger, disconnector & hammer, the trigger pull was clean & crisp. my groupings became tighter as a result. big improvement over the stock colt sear.

Love It..

150% improvement with Wilson hammer

Great part!!..

Went with this sear & a Bullet Proof disco. Only 2 minutes fitting on my safety & it works like a dream. Wilson has done good!

great drop in part..

Install with a bulletproof hammer for a trigger with a clean break. I had to take a little bit off the thumb safety engagement surface to get it to work with this sear. SA TRP Operator.

Wow!..

I just got the Bullet Proof Deluxe Sear and Wow was I Pleased. Very High Quality, Beautiful! Almost no work required. Ill be putting this in my other 1911 soon.

Wilson has no competition..

Crisp, Clean Un matched break. Do the whole wilson trigger job. You will have a whole new gun 10 times better.

Superb!!!..

...a little polish there, a little there, drop it in, but.... for superb, better, best, marvelous results... drop it all in a Wilson Combat Bulletproof! No worries! My baby is a lot more crispier than ever! Love it!!!

high quality, precision components..

I replaced the cheap internals: safety, sear, disco, slide release, mag release and extractor on my Colt 1991 with Wilson Bulletproof parts. After minor fitting, safety checks and live fire testing I now have a pistol that I can count on.

Ultra clean break!..

I replaced all my trigger components in my S&W with Bullet Proof parts and set the trigger to 3.25 lbs. Factory pull was about 4.75 and had a clean break. I was speechless after I got my gun back from my local gunsmith Clint at Coyote Creek in Rochester MN. These parts are amazing! I had a knowledgeable customer next to me give it a few pulls and he said “Wow, now that’s an amazing trigger. . . WOW”. Ultra clean break with this Sear and Disconnector! Great parts!

RIA 1911-A1 CS PRODJECT..

Supper part , matched nice with the commander hammer I had gotten . It feels like a differrent gun , nice & crisp !! Thanks WC !!

Great fit..

Dropped right in my Springfield Armory 1911, replaced mil spec parts all with Wilson Combat bullet proof parts. Very crisp trigger pull.

Hands Down Choice..

I have build my fair share of 1911s, I started using WC parts in all my build and havent looked back since. This Sear is nothing less than perfect, I took it out of its package and put it directly on my fitting jig, I did not have to do one thing to this sear!! it was perfect. I dropped it in along with a Bullet Proof hammer and it instantly gave it a crisp clean trigger!!! I will no longer use any other parts for a build! Thanks again WC!!!

Best Sear Available..

I purchased this sear to use with a Wilson 337B hammer and ultra light match trigger. The results were nothing short of amazing. The sear is of high quality, and fit and finish were excellent. All contact surfaces where correctly cut and highly polished. Everything about this sear says quality. Will be purchasing more for future builds.

Great combination with the 337B hammer..

The A2-Sear required minor fitting with my Springfield Trophy Match, but works perfectly. In combination with the 337B Hammer, trigger pull is crisp and without any creep, and the trigger breaks at around 2 1/2 - 3 pounds. Ive put some hundred rounds through the gun for a live-fire safety and function test - no problems at all, the trigger is just as I always wanted it to be. Excellent job, Wilson Combat!

Great quality..

This sear is great! Paired with a Wilson Combat hammer on my recent trigger job. I was worried because I didnt have the tools to dial in the pitch of the sear but it was done for me. I wish manufactures used quality parts like this in their pistols. Used in my Kimber Ultra CDP II with no modifications

Obvious this is a quality part..

You can see the quality in craftmanship in this part. Minor fitting but well worth the price and then some

Great Part..

I just finished installing and test firing my Colt Defender. Installed this sear and the hammer and dis connector that goes with in . Itwas a drop in on my Colt and all safety checks performed and passed . I now have a new trigger that is worth the money . If you buy the sear get every thing and do the full job.

Nice High Quality Sear..

This sear is far better than my stock one. I installed this along with WC Ultralight Hammer and it function very well. the material that they use on making this sear is really good and beefy. It really does look like its bullet proof. It required some minor fitting to fit my Loaded M1911-A1. but other than that its been functioning right. Highly recommended...

Best choice..

Bought this sear to match the 299 hammer and just dropped them in my Kimber Pro Carry II and trigger pull set at 31/2 lbs. Clean break no creep. I am all smiles.. You cannot go wrong with the quaility parts from Wilson Combat, great job!!!

great part..

just put into my colt great fit and function

easy easy easy..

Dear dropped right in my Auto Ordnance 1911, yet another great product from WC. Cant wait to go shoot it